*
*
Electrical panel Permit requirements The on-line allow is easily accessible for properties in lifwynnfoundation.org through a residential zoning district. Zoning district info is easily accessible on-line by clicking on E-Zoning.

You are watching: Aluminum wire size for 200 amp service

This permit will allow replacement that the existing electric panel approximately a preferably of 200 amps in the very same location.Note: part properties in lifwynnfoundation.org have an underground electric power feeding from PG&E. If your property has an underground strength feed, verify with PG&E that they can administer increased power for a bigger panel size.To identify if the proposed dashboard is sized accordingly for your requirements OR if you want to check out if the proposed panel is big enough for an all-electric house, please complete an electric panel sizing spreadsheet. An electric permit is forced for replacement and upgrade of the key electrical service panel prior to installation the the brand-new panel. Complying with is a listing of the basic requirements for electrical panel replacements based on the 2019 California electric Code. This directory is plan to administer general information, call the building Safety department for any questions or added information.General Requirements - The key electrical company shall be installed with strict conduit. Electrical metallic tubing may be used where the service drop is attached come the building. The business entrance cable may be used, noted the approved fittings are provided with the cable, such together a rain-tight company head or creating the cable goose-neck, taped or painted, and held securely in ar by a fitting authorized for the purpose. (Article 230)The minimum size organization conduit shall it is in 1-1/4”. The minimum size organization entrance cable shall it is in rated 100 amperes minimum for solitary family dwellings. For single family homes, the service disconnect means shall have a rating of less than 100 amperes, 3-wire. A larger service may be compelled for brand-new homes or additions to present homes based upon the actual fill calculations. (CEC 230.79(C))Service enntrance gate Conductors (Wires) – Conductors that extend throughout a roof shall have a minimum vertical clearance the 3’ over the roof surface for roofs sloped 4:12 or more (18” clearance required when conductors go into through the roof overhang/eave). The business head chandelier be located so that the company drops, in addition to the open up wires in between the organization head and also service drop, will have a minimum clearance that 10’ vertically above ground and 3’ radius native doors and windows. (Article 230.24)The neutral (grounded) conductor must be identified with white tape at both terminals. (Article 200.6(B)(4))Service entrance conductors and cables shall be approved for a wet ar and, when exposed to direct sunlight, chandelier be listed and marked as “sunlight resistant.” service entrance conductors and also conduit candlestick be sized according come the following table (based top top CEC chapter 9 table 1):
SERVICE enntrance gate CONDUCTORS SIZE and RATING
Service or Feeder RatingCopper ConductorsAluminum or Copper-CladAluminumMinimum ConduitSize
100 Amps#4 AWG#2 AWG1 ¼ inch
125 Amps#2 AWG#1/0 AWG1 ¼ inch
150 Amps#1 AWG#2/0 AWG1 ¼ inch
200 Amps#2/0 AWG#4/0 AWG1 ½ inch
The ground connection conductors should be identified by white or grey tape at both ends (200.6).Meter location - PG&E needs the elevation of the meter to be 48” to 66” over the ground. PG&E prohibits brand-new meters ~ above exterior walls surrounding to bedrooms or bedroom closets. A minimum horizontal clearance that 36” native the gas meter and piping is required.

See more: When Is The Force On A Current–Carrying Wire In A Magnetic Field At Its Strongest?

Working space - The clear working space in former of the dashboard shall it is in 30” vast by 36” deep v a minimum headroom clearance that 6’-6” (Article 110.26)Grounding of Services - grounding shall covers a consistent grounding electrode conductor operation from the panel to a ground pole (grounding electrode) and also to the cold water pipe. Grounding of the electrical company at the main water line need to be within the very first 5’ of water piping right into the building. The secret water business shall no be provided as the grounding electrode there is no supplemental electrode. For brand-new structures and enhancements to currently structures, a concrete encased floor electrode shall it is in installed. This chandelier consist of 20’ the ½” ceiling or zinc-coated rebar or bare copper wire in the section of the footing in call with earth. (CEC 250.52(A)(3)(1) and 250.52(A)(3)(2))For existing structures, the grounding electrode shall be nonferrous (copper), listed, and also not be much less than 5/8” in diameter. The electrode candlestick be set up such that at the very least 8’ of size is in contract through the soil. The upper finish of the electrode shall be flush v or listed below ground level unless the above-ground end and also the ground connection electrode conductor attachments is protected against physical damage. (CEC 250.52 (A)(5), 250.64(B))The forced grounding electrode conductor (from electrode come panel) size is listed in the following table:
GROUNDING ELECTRODE CONDUCTOR SIZING (Table 250.66)
Size of key PanelCopper ConductorsAluminum or Copper-Clad Aluminum
100 Amps#8 AWG#6 AWG
125 Amps#8 AWG#6 AWG
150 Amps#6 AWG#4 AWG
200 Amps#4 AWG#2 AWG
Bonding - Bonding the the hot, cold, and also gas currently is forced when the electrical panel is replaced. Bonding of the hot, cold, and also gas currently is compelled with water company replacements (if utilizing a much less conductive material than is existing) and for all re-pipes. Bonding candlestick consist the a constant bond jumper set up at the water heater in between the hot, cold, and gas lines. The bonding jumper shall be sized based upon the adhering to table. (CEC250.4(A)(4))
BONDING JUMPER SIZING (Table 250.102(C)(1))
Size of key PanelCopper ConductorsAluminum or Copper-Clad Aluminum
100 Amps#8 AWG#6 AWG
125 Amps#6 AWG#4 AWG
150 Amps#6 AWG#4 AWG
200 Amps#6 AWG#4 AWG
The electrical Panel permit is NOT obtainable on-line if friend are: installing the new electrical dashboard in a different location. installation a new electrical panel larger than 200 amps. Installing additional sub-panels with the brand-new electrical panel. Performing added electrical work in conjunction through the brand-new electrical dashboard installation.
If any type of of the above conditions apply, the permit shall it is in issued at the One-Stop allow Center, City Hall, 456 W Olive Avenue. Specific procedure information is accessible at the Building division web site.
InspectionsA minimum of two inspections are required, a energy release and a final. The utility release inspection must be scheduled once the brand-new panel is installed and also ready to it is in hooked up the PG&E supply. The structure inspector will administer a energy release type which will need to be provided to PG&E to have the supply hooked approximately the new panel. A wire lath inspection is compelled for stucco repairs. A final inspection should be booked after all of the job-related is complete.
*