MANUFACTURED BY

White Sewing device Company

Cleveland, Ohio, U.S.A.

You are watching: White rotary sewing machine model 43 manual

Never run device with needle threaded without products under presser foot. Run device so that top side that hand wheel moves from you.

TO collection NEEDLE

Raise the needle-bar to its greatest point; loosen the thumbscrew and press it come the left to allow the shank that the NEEDLE to pass up in between the clamp and also needle-bar as far as it will certainly go, flat side to the best -- the NEEDLE gift flattened on one next so that will collection itself perfectly, climate fasten securely by tightening thumb-screw.

To prevent loosening that the needle, always use a screw driver to fasten the same, the needle nut being slotted for the purpose.

The needle, when descending, must pass central in the needle hole from FRONT come REAR, but close to the appropriate side that the hole, together it avoids the needle indigenous glancing right into the race and being recorded by the shuttle.

NEEDLES and also THREAD TO be USED

The most IMPORTANT factor to consider is to buy and also use perfect needles -- no bent, nor dull points. We specifically request ours dealers and also their client to buy your needles and oil indigenous us. WHITE F. R. NEEDLES have to be offered on this machine.

The size of that needle have to conform to the dimension of the thread and also both be an ideal to the product sewed. Usage as well a needle as will certainly permit the thread come pass easily through the eye.

*

*
TO remove BOBBIN situation FROM SHUTTLE

Raise the take-up to its highest possible point. With the ignorance and 2nd finger that the left hand clasp bobbin situation as displayed in cut, climate lift latch S v the third finger, when bobbin instance may be readily withdrawn from shuttle F. Watch below

TO remove SHUTTLE FROM spaceship RACE

First remove the fail case. Revolve the machine back on its hinges, then revolve the device in the very same direction together in sewing until the allude of the needle simply enters the needle plate hole; press on rear end of latch G and also at the very same time traction shuttle gyeongju cover far from shuttle and also toward latch G native under pen H; the shuttle have the right to now it is in removed.

When shuttle has been removed from race be sure to clean both, and oil the gyeongju slightly prior to replacing. Sometimes oil contempt in feet on race cap marked V over and pen W in shuttle, see fig 9.

TO replace THE SHUTTLE

Turn the machine in direction for sewing till the point of the needle just enters the needle bowl hole; take the shuttle by the center pin W v the left hand and place the in the race, therefore that suggest of shuttle will certainly be indigenous you and

*
over arrowhead on thread cast of, so that the holes in the shuttle will drop on come driving pins in race, then replace the shuttle gyeongju cover.

DO NOT force the shuttle right into race. It will get in readily when in suitable position.

Should the machine at any time time act bad in sewing or running it would certainly be well to eliminate shuttle and clean it and the race, i m sorry is yet a moment"s work.

To replace the failure case, it need not be organized as once removing, yet simply on slide it top top the pin in shuttle, v the anxiety projecting upward, and also push it right into shuttle as much as it will certainly go, as soon as the feather latch will certainly pass over and retain the in that position.

The thread should be allowed to project about one inch from bobbin situation tension.

TO WIND BOBBIN

*
Place spool ~ above spool pin, pass the subject down through the behind hole in eight of cover plate, climate to the left under and also over the eight down with front hole. Placed the finish of thread with hole U in bobbin from inside out, place bobbin ~ above bobbin more comprehensive spindle, advanced winder for this reason belt will certainly drive it, loosen ignorance screw in hand wheel, run the machine as in sewing, holding on come the end of thread till winding is started, then break off thread and finish winding.

LOWER TENSION

Fig. 8 represents the failure case. To manage the lower tension, rotate the screw T come the appropriate to tighten, and to the left to ease the same.

TO thread BOBBIN situation TENSION

Place failure in situation so that thread will come native bobbin on same side together hole B in bobbin case; pass thread through slot A to hole B thence across opening, drawing it under lip C climate pull it up till thread passes the end under anxiety spring D.

The stress and anxiety on bobbin instance should be the same as the top tension.

*
*

DIRECTIONS for THREADING

Place the spool top top spool pin, take the object in her left hand holding it taut with the right throughout the totality

*
threading operation. Pass thread native spool over examine spring K at height of face and also down under point L.

Now traction thread upward till it passes through the eye of spring N and also into notch O, climate into finish of take-up p then down with slot R in finish of needle bar and through eye that needle from left to right, allowing about 3 inch of thread once take-up is in ~ its highest point.

To draw up the reduced thread, raise the presser-foot, take host of finish of top thread and also turn the hand wheel once round, (moving upper side of wheel from you), i m sorry will attract the reduced thread up through needle hole.

Pass the end of both subject under the presser-foot and you will be all set to sew.

Note, -- perform not operation the maker with the presser-foot under on the feeding without fabric under it. Execute not pull towel to or from you in together a manner as to bend the needle.

THE TENSION

The illustration over represents the stress Regulator and also Indicator for the upper thread, one entirely brand-new and helpful device.

The fifty percent circle is marked with a scale running native 1 come 8, with words "loose" in ~ Number 1 and also "tight" at Number 8 , Number 1 being the slack and also Number 8 the tightest tension.

TO adjust THE length OF STITCH

The regulator is located at the right finish of the machine on the front next or arm.

TO SHORTEN stitch move lever down.

TO LENGTHEN stitch move lever up. Number 1 suggests the shortest, and also Number 7 the longest stitch

OIL locations AS suggested BELOW

*

TO control THE TENSION

To ease the tension, turn the thumbscrew ~ above the dial come the left i beg your pardon will move the guideline towards No. 1. To tighten it, rotate to the right, relocating the reminder towards No. 8.

By this means the exact same tension can always be duplicated, therefore obviating the need of speculative trials, as is the instance with various other machines. If a tight anxiety is desired, both upper and also under threads must necessarily it is in tight.

If the upper thread is tight and also the reduced thread loose, the upper thread will be attracted to the peak thus:

*

If the lower thread is as well tight, it will be drawn straight top top the bottom of the goods, thus:

*

When girlfriend desire the items to look alike ~ above both sides, and also be elastic, balance the stress and anxiety thus:

*

THE stress RELEASER

The anxiety releaser is activate by the presser-bar lifter. By way of it, all stress and anxiety is taken off the upper thread when the presser-foot is raised, and also the work deserve to be taken the end without pulling the thread under by hand.

***PARTICULAR an alert --- The stress and anxiety cannot be regulated when the elevator is up due to the fact that the Releaser is operated by the presser-bar lifter.

TO COMMENCE WORK

In threading the needle and bobbin instance respectively, you must leave one end about two customs in size to each. Host the end of the upper thread loosely in the left hand, and with the appropriate hand tenderness revolve the hand-wheel till the needle overcome to its lowest suggest and returns, a loop will certainly be formed through i beg your pardon the shuttle will pass, and, together the needle ascends that will attract up the lower or shuttle thread, and also the machine is prepared for handy operation.

TO remove WORK

Stop the maker with the take-up in ~ its highest possible point; raise the presser-foot with the lifter i beg your pardon slackens the top thread; then take organize of your work with her left hand and also pull it straight from you, keeping the top thread in the slot the the presser-foot, i m sorry will stop bending the needle.

Now raise the work and also draw the threads into the subject cutter on the presser-bar and also pull downward, which will cut the object the proper length come commence occupational again.

EXPLANATION OF difficulties THAT SOMETIMES happen WITH BEGINNERS

If the upper thread breaks, it might be caused by the needle not being effectively set, or the device not threaded correctly, or the upper anxiety too tight, or the thread uneven and also the needle too tiny for it, or the needle eye as well sharp, or the presser-foot attached come the an equipment so the the needle rubs it in passing.

If the under thread breaks, it may be brought about by the bobbin situation being improperly threaded, or too much tension top top it, or through the bobbin gift wound too complete so that the thread slips end the end of the fail in the failure case.

If the needle breaks, it is more than most likely your very own fault, led to by pulling the goods to or from friend in together a manner the the needle strikes the neck plate and also is bound to break. The needle may however, break in trying come sew extraordinary heavy seams when the press on the presser-foot is not hefty enough. Come create much more pressure ~ above the products turn the presser-bar seed on optimal of the presser-bar come the right; to decrease the push turn it come the left.

If the an equipment makes loop stitches, the is most sure to be brought about by too loosened tension both top and also bottom.

If the maker skips stitches, the needle is one of two people bent or not in the best position.

If the stitches room not even, it may be led to by the presser-foot not relaxing evenly top top the towel sewed, or through the feed no being high enough, or by the stitch being also short, or through pulling the cloth, or by using as well fine a needle through too outlet or uneven thread.

If the maker should be run without sewing and also thread gain in the shuttle gyeongju making the an equipment run heavy, take out the fail case and also run the an equipment in the wrong direction; that will reduced the thread out.

See more: Can Pregnant Women Drink Chocolate Milk S Harmful For Pregnancies?

NOTICE --- The leather tape should constantly be tight sufficient not to slip. If it slips, or walk not pressure the needle with thick goods, cut off a really short piece and re-adjust the ends. The belt should not it is in so tight as to prevent and easy activity of the machine.